原理图与封装引脚编号对应问题

GoPo

我画了一个BGA100的封装，在原理图中，字母是从Ａ～Ｊ。用向导画出来的封装字母从Ａ～Ｋ，没有Ｉ，导入网表的时候就会产生引脚编号不匹配的错误。
' O; \1 i$ P" ?
请问能不能很方便地改封装中的引脚编号？

错误信息如下：
( g# o0 Q: ?9 |  p5 F% r3 i#2   ERROR(305) Device/Symbol check error detected.
Symbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' has extra pin 'K1'.
/ t- ~8 e. I- h) Z( W, z# iSymbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' has extra pin 'K2'.
& N' u2 ^( g: R# V& V/ MSymbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' has extra pin 'K3'.
+ O8 F& p4 C1 i2 oSymbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' has extra pin 'K4'.
( \' z2 r2 X( K2 Y; KSymbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' has extra pin 'K5'.
. Z7 s, s+ N$ u2 ]) XSymbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' has extra pin 'K6'.
1 W. Q! [3 L/ f, cSymbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' has extra pin 'K7'.
6 s0 ]0 S9 v" q1 @' ySymbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' has extra pin 'K8'.
' k/ ?8 `7 X+ b4 K9 H3 ZSymbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' has extra pin 'K9'.
& ~# C7 |* R% f& rSymbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' has extra pin 'K10'.
Symbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' is missing pin 'I2'.
6 v4 l( W: c% \# s- {2 MSymbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' is missing pin 'I3'.
. ^* s- A1 ^" d7 _! N0 x, kSymbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' is missing pin 'I6'.
Symbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' is missing pin 'I5'.
Symbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' is missing pin 'I1'.
* }+ W8 F; t) `( m1 nSymbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' is missing pin 'I4'.
4 q  w- ~, J' V. P8 _Symbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' is missing pin 'I7'.
Symbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' is missing pin 'I8'.
* ^" Q+ A5 `6 d- ESymbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' is missing pin 'I9'.
! ^1 r3 j+ d- \% o" z2 ASymbol 'BGA100' for device 'VCSEL_BGA100_VCSEL' is missing pin 'I10'.

xiuzhong200402

我也明白了!

GoPo

原帖由 kxx27 于 2008-4-28 16:45 发表
0 i: Y% Q2 [+ W7 G2 CI 在建BGA时是默认没有的，你不能将它改了。

. H) R! _" u/ j) ]
经过一番摸索，我解决了。用edit->text，点选J，在命令里输Ｉ就可以把它改成Ｉ了。把所有的都改过来之后错误就没了

panhaojie

学习了

gino

我也去建个ＢＧＡ　试哈