hspice add model ?

allen_lyl

哪位前辈指点一下，已有一个connector的model（AirMax_VH_100ohm_RAR_100ohm_3pair_2mm_MC2C_AB.s24p），不知道该怎么用，请问在hspice里面怎么用语句和前后的trace链接起来？

wakinoda

如下：
; s3 C6 h- S  W  _' r1 U. OS1 tx_1 rx_1 tx_2 rx_2 ... tx_12 rx_12 0 mname=AIRMAX
.model AIRMAX S TSTONEFILE = AirMax_VH_100ohm_RAR_100ohm_3pair_2mm_MC2C_AB.s24p
注意你的s-parameter模型端口一定要和HSPICE里定义的端口一致

allen_lyl

太好了！真的太感激了！这个model是厂家提供的，看不到s-parameter模型端口？是不是要在模型里面自己来定义端口啊？怎么定义？

! q# A' O1 I* S  Q3 c$ }别的模型可以看到有端口，这个就没有！我不知道是不是要重新定义端口？然后才可以用啊！前辈请指教啊！

wakinoda

Part No.是多少？不可能没有配套的note可以查

allen_lyl

没有看到part number啊！

allen_lyl

这是model的前半部分，接下来没有上传的部分，全是数据！model信息就这么多！
! -----------------------------------------------------------------------------
! By using this Touchstone file you agree to the following terms and conditions.
!
# N/ Z6 x  Q1 U" T! Copyright
" h, p* R' `1 n6 B$ v9 \! \!
!        Copyright 2008 FCI
!
! This Touchstone file has been created for our customers and associates.
! FCI retains copyright in the entire text and graphic content of
1 U- j7 d" r$ K* o' J: a! this file.  You may view, copy and distribute this file freely.
! You are not authorized to modify this file in any manner without
! the written permission of FCI.  All other rights are reserved by FCI.
!
; [; J2 a6 ?0 b5 F7 R2 g0 Q- h!
! Information
6 X( J  T8 J7 U) i" x9 a: ~; ]  r!
% D7 d- Q/ k4 s* f' E5 W: t! FCI endeavors to use its reasonable efforts to place accurate and
! up-to-date information in this Touchstone file.  However, this file is
# p. s7 c8 o4 Z! provided on an as is basis.  FCI GIVES NO WARRANTY, EXPRESS OR
! IMPLIED, WITH RESPECT TO ANY INFORMATION PROVIDED IN THIS FILE,
; n0 F2 ~. x9 o; ?' W! INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
! MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT.
8 R) G" B. L) O" M4 N! H! FCI SHALL NOT BE LIABLE FOR ANY DIRECT, SPECIAL, INDIRECT,
/ O! I6 _0 Q( V+ }8 a! CONSEQUENTIAL, PUNITIVE OR OTHER DAMAGES BASED ON USE OF THIS FILE.
!
- _8 @# B+ p6 R  s$ X+ Y' F1 H! Trademarks
!
! This file may include names for products that are trademarks
! used by FCI and FCI Group companies.  
! Unauthorized use or misuse of such trademarks is prohibited.
  e, t8 W$ r  v+ ~! F! -----------------------------------------------------------------------------
( J4 [" n- m, Y- c2 P2 m!
4 q- W/ @3 i5 H% @+ F#        Hz        S        RI        R        50
. g% n& l; i) e: M4 p) `$ E6 y, S50000000        0.005840144402        0.01261774643        0.0001914812071        0.01131354154        0.0001832736293        0.0006898859316        0.0001672425175        0.0006812842794       
5 [& z6 i+ T4 M-3.161805653e-005        0.000213994954        0.0001748447366        -3.27040591e-005        -1.77844438e-005        0.002900904769        0.0003273053863        0.002257234118       
2 f9 _- o+ Z( \- n6 K0.0001009970176        0.0001975123932        -9.780656986e-005        0.0001596273876        8.271699608e-005        -7.908730405e-005        6.400454777e-005        0.0001161377143       
  }/ Z  R. {; Q, [0.9966848883        -0.03432331243        -0.0001061817411        -0.00464460707        0.0003299924736        -0.0002976503138        -0.0003201485131        -0.0002034368166       
-0.0001260793423        0.0001250651903        -0.0001258324326        3.363360506e-005        -0.0001109053014        -0.002098042675        -0.0002535615513        -0.001512366408

wakinoda

这你的要跟FCI要model note，否则只能自己根据24port自己去试，比如用1、3做输入，2、4做输出，看看S11,S21这些参数正常与否。

allen_lyl

好的！谢谢！

zippoland

好东东

liweizhe1002

长见识了，

abel_yeh

allen_lyl 发表于 2009-5-14 09:18
这是model的前半部分，接下来没有上传的部分，全是数据！model信息就这么多！
! ------------------------ ...

: `! j% ?2 p. T' g9 y( i- g  这个你直接找FCI告诉你定义。不过他们一般的定义方式是前半部分是HEADER端，后半部分是RECPT端。即1对13，2对14...12
1 i1 Z6 V' @+ a$ O对24.