EDA365电子论坛网
标题:
artwork出现的警告是否可以不理会(急等回复)
[打印本页]
作者:
elmma
时间:
2008-4-24 09:23
标题:
artwork出现的警告是否可以不理会(急等回复)
1.================================================================
* O( B8 }0 }% j) x
PROCESSING FILM < TOP.art > ...
7 o/ E4 g) B9 D9 G
================================================================
' P; ~5 c+ ? F! p' \: c
FILM PARAMETERS :
" @5 m& a7 r+ h! R% m
---------------------------------------------------------
# J! r- T& z7 v7 J
Undefined line width 6.00
5 y0 Z+ G+ w% T ~
Mirror code NONE
2 S0 H6 y5 U+ S! Y' [/ e! U& _, M
Rotate angle NONE
$ |/ y6 K7 Q5 c, _' C9 e0 v% }8 j
Offset x: 0.00
2 |5 s0 X( V5 [$ f' i" I
Offset y: 0.00
' `( H8 q- Q2 K, J
Plot negative NO
* j4 A4 j3 S3 c+ w+ l: b
Suppress unconnected internal pads NO
: q7 M# w* h9 l
WARNING: 0 width line found at (50.00 0.00)
3 l4 ?1 |1 a" w) ^3 f) g6 L9 e5 l6 |
' N) U) b& m2 N3 h
2.FILM PARAMETERS :
" x# o; F1 u; ^
---------------------------------------------------------
$ v' X' a8 c1 A9 t2 Q& u4 o, w( ?
Undefined line width 6.00
1 t' ~/ ~8 e$ {$ m" P/ }
Mirror code NONE
% V/ r$ u% k* o! i3 Z
Rotate angle NONE
: H: e b- F& [, R6 O
Offset x: 0.00
# I6 b9 C+ b0 M6 u2 C* b; p
Offset y: 0.00
4 B! F9 ]8 Y7 V# r5 G
Plot negative YES
) a$ f0 U2 c& c6 Y
Suppress unconnected internal pads NO
4 g% P1 H+ a1 p! L& T
WARNING: Layer polarity of class ETCH subclass VCC does not
3 z/ N8 n8 I6 e! I* r& N
match film polarity of Negative. DRC may be unreliable.
% p- X3 A3 D* A! g" v
如果要改正,针对以上两个警告,该怎么改正啊.谢谢回答
3 O3 L' l8 N% w; C0 a7 G( B
8 [0 `% K {1 i6 h
[
本帖最后由 elmma 于 2008-4-24 13:12 编辑
]
作者:
elmma
时间:
2008-4-24 10:53
NC-drill Legend时出现一下错误,如何改正
9 X0 p& U6 Y5 u
Begin processing drill holes.
+ F3 V# S) f4 ?) z5 a! v5 o v
Warning : Hole 32.00-0.00-C-P-0.00-0.00 uses multiple drill figures.
. ]4 O7 G S- h4 ~& l
Warning : Hole 38.00-0.00-C-P-0.00-0.00 uses multiple drill figures.
6 J: j4 U, ?8 V5 B3 R
Warning : Hole 100.00-0.00-C-P-0.00-0.00 uses multiple drill figures.
$ ?$ Z3 ]" d/ ?* X% F
End processing drill holes.
欢迎光临 EDA365电子论坛网 (https://eda365.com/)
Powered by Discuz! X3.2
3 O3 L' l8 N% w; C0 a7 G( B